My two-month internship ended with Doug Adams and I’m now going back to Duncan MacMaster’s for one more month long internship. This will be my last internship while I am in school.
My first day back at Duncan’s was relaxing and short. It was just before Thanksgiving break so we spent the time catching up and discussing the upcoming projects. I told him all the things I had done and learned at Doug’s. Then Duncan showed me the projects he will be doing and the things I will get to help him with. One the biggest project I will be helping with is a console table made out of cherry for a local costumer who wants it before Christmas. Another project is a small Japanese style altar table for another local customer.
The first project Duncan gave me when I came in the next week was to work on the Japanese style alter table. Duncan had already started and mostly finished the little table. The top is a beautiful, old, odd shaped piece of wood the clients had found years ago. They wanted Duncan to make a Japanese alter table out of it for them. Duncan designed a square base to hold the beautiful piece of wood. He cut the top two inches or so off the base so an inner box could be attached allowing the top to slide on and off if needed.
The first step was to drill pilot holes in the top of the base where it would eventually be screwed onto the tabletop. I started by measuring and marking where the holes should go and set up a fence on the drill press so the piece would stay in place while drilling. Using a countersink drill bit I drilled the holes.
Next I measured and cut the pieces for the inner box. Before gluing them up I double checked to make sure they all fit properly inside the top of the base. Then I glued the pieces together and one again made sure they fit properly into the base. After that I glued the inner box to the top of the base, clamped them, and set it aside to dry. The box that I glued inside the top of the base will slip into the bottom of the base and eventually be held on with wooden pegs.
Meanwhile, Duncan had started the cherry console table. He had the top finished and the pieces for the legs, aprons, and drawer fronts cut. He had also partially cut the mortises in the legs using the table saw. This assured that the mortises would be perfectly straight and clean. But, due to the saw blade being round there was a little wood near the bottom of the mortise that didn’t get cut. My next assigned job was to finish the mortises and get them fully cleaned out. First I used the drill press to clean out as much as possible. This was fairly quick and easy because I only needed to make a few holes before I reached the point where the table saw had already cut. One I got to that point I could pop out the inner pieces of wood.
Next, Duncan handed me an assortment of Japanese chisels, each one allowing me to more easily work on different aspects of the mortise. I got the mortises cleaned out but detail work would need to be done once the tenons were finished and matched to the proper mortise to ensure as close to a perfect fit as possible.
Duncan got the tenons cut to proper size on the table saw and handed them to me to cut a miter joint on the end of each. I made certain to cut them all the correct way.
Once the mortises were finished Duncan was able to taper the legs and fit the tenons on. Duncan had to hand plane a few areas on the legs to make the apron fit flush against them.
Next we sanded the legs. Duncan had me hand sand the top of the legs in such a way to keep the angle sharp where the legs taper off; if a pad sander were used on that area that angle would have rounded.
The next step I helped Duncan with was gluing the mortise and tenons together. Duncan had cut grooves out of a lip on then underside of the tabletop where the legs would fit. With the tabletop flipped upside down Duncan put all the pieces in their place and we did a dry fit making sure everything fit perfectly.
I still find glue ups to be stressful. First of all when you put the glue on you have to go as fast as possible. I am still very slow at this part for some reason. I had glued only a few surfaces on two mortises in the same time it took Duncan to glue all the tenons and the other two mortises. And secondly, although we had everything fitting perfectly for the dry run once the glue was on and the clock was ticking the pieces suddenly didn’t want to fit together. One of the legs wouldn’t go on all the way so Duncan whacked it several times with a hammer. This produced one of the loudest sounds I had heard up close; my ears were ringing. This wasn’t working so Duncan grabbed a large clamp and cranked it until the leg finally popped into place. Then we took smaller clamps and quickly popped all the joints together putting clamps on and taking them off and readjusting them until all the pieces finally popped together. Once everything fit we took all the clamps off and reclamped it in such a way to pull the mortise joints in tight onto the tenons.
Once the joints had dried we unclamped it and I moved onto my next task; I was to make boxes that would fill in the space around the drawers. Duncan had already cut the long pieces so I measured and marked the short pieces that were still needed and cut them to size. I did this slowly cutting a little off at a time to make sure all the pieces came out the same size. Then I measured and marked where the screws should go on the correct boards then I drilled the pilot holes. Next I glued and clamped the pieces making sure to make them flush with each other. Then using the same pilot holes I had already drilled into some of the boards I now used them to drill into the other boards they are now attached to. Then I screwed the pieces together and unclamped them. Then I checked that they fit properly on the underside of the table.
It’s been a really good first week back. It’s been interesting and fascinating to see the way Duncan designs and builds furniture. He thinks about all the aspects of the function of the piece of furniture and incorporates supports where needed. He makes furniture to last and he puts his very best into it.